Onionmixer: NeXTSTEP DRIVER KIT 잘못된 설정 복구 내용 추가

2017-10-11T15:32:37Z

NeXTSTEP DRIVER KIT 잘못된 설정 복구 내용 추가

← Older revision		Revision as of 15:32, 11 October 2017
Line 4:		Line 4:

	If you can't restart your system because of a bad configuration or because of bugs in your driver, try restarting with a default configuration. To do this, type the following at the '''boot:''' prompt when the system starts:<BR>		If you can't restart your system because of a bad configuration or because of bugs in your driver, try restarting with a default configuration. To do this, type the following at the '''boot:''' prompt when the system starts:<BR>
			설정이 잘못되었거나 드라이버의 버그로 인해 시스템을 다시 시작할 수없는 경우에는 기본 설정으로 다시 시작하십시오. 이렇게 하려면 '''boot:''' 프롬프트에서 시스템이 시작될때 다음을 입력하십시오:

	<syntaxhighlight lang="objc">		<syntaxhighlight lang="objc">
Line 11:		Line 12:

	This causes the boot program to use '''Default.table''' in '''System.config''' as the system configuration, which usually works. Once you've started up, log in as '''me''' or '''root''' and use Configure to fix the rest of the configuration.<BR>		This causes the boot program to use '''Default.table''' in '''System.config''' as the system configuration, which usually works. Once you've started up, log in as '''me''' or '''root''' and use Configure to fix the rest of the configuration.<BR>
			위의 작업을 진행하면 부트 프로그램은 '''System.config''' 의 '''Default.table''' 을 시스템 설정으로 사용하게 되며, 일반적으로 (별 문제없이)작동합니다. 시작한 후에는 '''me''' 또는 '''root''' 로 로그인하고 Configure 를 사용해서 나머지 설정을 수정하십시오.


	If you still can't start the system, try starting in single-user mode and editing the bundles by hand. This is risky since the configuring process has many "rules of thumb," and you might not know all the effects of a change. To restart in single-user mode, type the following at the '''boot:''' prompt after you restart:<BR>		If you still can't start the system, try starting in single-user mode and editing the bundles by hand. This is risky since the configuring process has many "rules of thumb," and you might not know all the effects of a change. To restart in single-user mode, type the following at the '''boot:''' prompt after you restart:<BR>
			여전히 시스템을 시작할 수 없으면 단일 사용자 모드(single-user mode)에서 시작해서 bundles 을 수동으로 편집해 보십시오. 설정 프로세스에 많은 "엄지 손가락 법칙(rules of thumb)<ref name="역자주11">https://m.blog.naver.com/PostView.nhn?blogId=good2gether&logNo=60124330296&categoryNo=27&proxyReferer=https%3A%2F%2Fwww.google.co.kr%2F</ref>"이 있기 때문에 위험할 수 있으므로, 변경으로 일어나는 모든 영향을 알지 못할 수도 있습니다. 단일 사용자 모드에서 다시 시작하려면 '''boot:''' 프롬프트에서 다음을 입력하십시오:

	<syntaxhighlight lang="objc">		<syntaxhighlight lang="objc">
Line 21:		Line 24:

	You can then use a single-user mode editor (such as '''vi''' or '''emacs''') to edit the configuration bundles.<BR>		You can then use a single-user mode editor (such as '''vi''' or '''emacs''') to edit the configuration bundles.<BR>
			그런 다음 단일 사용자 모드에서 편집기('''vi''' 또는 '''emacs''' 같은)를 사용해서 설정 bundles 을 편집할 수 있습니다.


			==Notes==
			<references />

			[[Category:NeXTSTEPDriverKit]]

Onionmixer: NeXTSTEP DRIVER KIT 잘못된 설정 복구 내용 추가

2017-10-11T12:00:47Z

NeXTSTEP DRIVER KIT 잘못된 설정 복구 내용 추가

New page

;Recovering from a Bad Configuration

==잘못된 설정 복구(Recovering from a Bad Configuration)==

If you can't restart your system because of a bad configuration or because of bugs in your driver, try restarting with a default configuration. To do this, type the following at the '''boot:''' prompt when the system starts:<BR>

<syntaxhighlight lang="objc">
boot: config=Default
</syntaxhighlight>

This causes the boot program to use '''Default.table''' in '''System.config''' as the system configuration, which usually works. Once you've started up, log in as '''me''' or '''root''' and use Configure to fix the rest of the configuration.<BR>

If you still can't start the system, try starting in single-user mode and editing the bundles by hand. This is risky since the configuring process has many "rules of thumb," and you might not know all the effects of a change. To restart in single-user mode, type the following at the '''boot:''' prompt after you restart:<BR>

<syntaxhighlight lang="objc">
boot: mach_kernel -s config=Default
</syntaxhighlight>

You can then use a single-user mode editor (such as '''vi''' or '''emacs''') to edit the configuration bundles.<BR>

NeXTSTEPDRIVERKIT:Chapter4 4 - Revision history

Onionmixer: NeXTSTEP DRIVER KIT 잘못된 설정 복구 내용 추가

Onionmixer: NeXTSTEP DRIVER KIT 잘못된 설정 복구 내용 추가