Smalltalk80LanguageImplementation:Chapter 28

From 흡혈양파의 번역工房
Revision as of 09:46, 9 May 2014 by Onionmixer (talk | contribs) (정오표 수정)
Jump to navigation Jump to search
Chapter 28 Formal Specification of the Interpreter

Formal Specification of the Interpreter

The main loop of the Smalltalk-80 interpreter fetches bytecodes from a CompiledMethod sequentially and dispatches to routines that perform the operations the bytecodes indicate. The fetchByte routine fetches the byte indicated by the active context's instruction pointer and increments the instruction pointer.

fetchByte
    | byte |
    byte  memory fetchByte: instructionPointer
        ofObject: method.
    instructionPointer  instructionPointer + 1.
    byte


Since process switches are only allowed between bytecodes, the first action in the interpreter's main loop is to call a routine that switches processes if necessary. The checkProcessSwitch routine will be described with the process scheduling primitive routines in the next chapter. After checking for a process switch, a bytecode is fetched (perhaps from a new process), and a dispatch is made to the appropriate routine.

interpret
    [true] whileTrue: [self cycle]
cycle
    self checkProcessSwitch.
    currentBytecode  self fetchByte.
    self dispatchOnThisBytecode


The table on page 595 lists the Smalltalk-80 bytecodes. The bytecodes are listed in ranges that have similar function. For example, the first range includes the bytecodes from 0 through 15 and its entry is shown below.

0-15        0000iiii        Push Receiver Variable        #iiii


Each range of bytecodes is listed with a bit pattern and a comment about the function of the bytecodes. The bit pattern shows the binary representation of the bytecodes in the range. 0s and ls are used in bit locations that have the same value for all bytecodes in the range. Since all numbers from 0 through 15 have four zeros in their high order bits, these bits are shown as 0000. Lower case letters are used in bit locations whose values vary within the range. The value of each letter can be either 0 or 1. The letters used in the pattern can be included in the comment to refer to the value of those bits in a specific bytecode in the range. The comment for the first range of bytecodes indicates that the low-order four bits of the bytecode specify the index of one of the receiver's variables to be pushed on the stack.


The variable bits in a bit pattern are also sometimes used as a zero-relative index into a list included in the comment. For example, the entry

120-123        011110ii        Return (receiver, true, false, nil) [ii] From Message


specifies that the bytecode 120 returns the receiver, bytecode 121 returns true, bytecode 122 returns false and bytecode 123 returns nil.


The entries for bytecodes that take extensions will include more than one bit pattern. For example,

131        10000011        Send Literal Selector #kkkkk With jjj Arguments
           jjjkkkkk


There are four basic types of bytecode.

  • stack bytecodes move object pointers between the object memory and the active context's evaluation stack. These include both the push bytecodes and store bytecodes described in Chapter 26.
  • jump bytecodes change the instruction pointer of the active context.
  • send bytecodes invoke CompiledMethods or primitive routines.
  • return bytecodes terminate the execution of CompiledMethods.


Not all of the bytecodes of one type are contiguous, so the main dispatch has seven branches each of which calls one of four routines (stackBytecode, jumpBytecode, sendBytecode, or returnBytecode). These four routines will be described in the next four subsections.

dispatchOnThisBytecode
    (currentBytecode between: 0 and: 119) ifTrue: [self stackBytecode]. 
    (currentBytecode between: 120 and: 127) ifTrue: [self returnBytecode]. 
    (currentBytecode between: 128 and: 130) ifTrue: [self stackBytecode]. 
    (currentBytecode between: 131 and: 134) ifTrue: [self sendBytecode]. 
    (currentBytecode between: 135 and: 137) ifTrue: [self stackBytecode]. 
    (currentBytecode between: 144 and: 175) ifTrue: [self jumpBytecode]. 
    (currentBytecode between: 176 and: 255) ifTrue: [self sendBytecode]


The bytecodes 176-191 refer to Arithmetic Messages. These are

+,-,<,>,< =, > =, =, ~=, *, /, \\, @, bitShift:, //, bitAnd:, bitOr:


The bytecodes 192-207 refer to Special Messages. These are

at:*, at:put:*, size*, next*, nextPut:*, atEnd*, = =, class, blockCopy:, value, value:, do:*, new*, new:*, x*, y*


Selectors indicated with an asterisk (*) can be changed by compiler modification.

Range Bits Function
0-15 0000iiii Push Receiver Variable #iiii
16-31 Push Temporary Location #iiii
32-63 001iiiii Push Literal Constant #iiiii
64-95 010iiiii Push Literal Variable #iiiii
96-103 01100iii Pop and Store Receiver Variable #iii
104-111 01101iii Pop and Store Temporary Location #iii
112-119 01110iii Push (receiver, true, false, nil, -1, 0, 1, 2) [iii]
120-123 011110ii Return (receiver, true, false, nil) [ii] From Message
124-125 0111110i Return Stack Top From (Message, Block) [i]
126-127 0111111i unused
128 10000000
jjkkkkkk
Push (Receiver Variable, Temporary Location, Literal Constant, Literal Variable) [jj] #kkkkkk
129 10000001
jjkkkkkk
Store (Receiver Variable, Temporary Location, Illegal, Literal Variable) [jj] #kkkkkk
130 10000010
jjkkkkkk
Pop and Store (Receiver Varialbe, Temporary Location, Illegal, Literal Variable) [jj] #kkkkkk
131 10000011
jjjkkkkk
Send Literal Selector #kkkkk With jjj Arguments
132 10000100
jjjjjjjj
kkkkkkkk
Send Literal Selector #kkkkkkkk With jjjjjjjj Arguments
133 10000101
jjjkkkkk
Send Literal Selector * kkkkk To Superclass With jjj Arguments
134 10000110
jjjjjjjj
kkkkkkkk
Send Literal Selector #kkkkkkkk To Superclass With jjjjjjjj Arguments
135 10000111 Pop Stack Top
136 10001000 Duplicate Stack Top
137 10001001 Push Active Context
138-143 unused
144-151 10010iii Jump iii+1 (i.e., 1 through 8)
152-159 10011iii Pop and Jump On False iii+1 (i.e., 1 through 8)
160-167 10100iii
jjjjjjjj
Jump (iii-4)*256+jjjjjjjj
168-171 101010ii
jjjjjjjj
Pop and Jump On True ii*256+jjjjjjjj
172-175 101011ii
jjjjjjjj
Pop and Jump On False ii*256+jjjjjjjj
176-191 1011iiii Send Arthmetic Message #iiii
192-207 1100iiii Send Special Message #iiii
208-223 1101iiii Send Literal Selector #iiii With No Arguments
224-239 1110iiii Send Literal Selector #iiii With 1 Argument
240-255 1111iiii Send Literal Selector #iiii With 2 Arguments
The Smalltalk-80 Bytecodes


Stack Bytecodes

The stack bytecodes all perform simple operations on the active context's evaluation stack.

  • 107 bytecodes push an object pointer on the stack
    • 99 push an object pointer found in the object memory
    • 7 push a constant object pointer
    • 1 pushes the interpreter's active context register (activeContext)
  • 18 bytecodes store an object pointer found on the stack into the object memory
    • 17 of these also remove it from the stack
    • 1 leaves it on the stack
  • 1 bytecode removes an object pointer from the stack without storing it anywhere.


The routines used to manipulate the stack were described in the section of the previous chapter on contexts (push:, popStack, pop:). The stackBytecode routine dispatches to the appropriate routine for the current bytecode.

stackBytecode
    (currentBytecode between: 0 and: 15) ifTrue: [self pushReceiverVariableBytecode].
    (currentBytecode between: 16 and: 31) ifTrue: [self pushTemporaryVariableBytecode].
    (currentBytecode between: 32 and: 63) ifTrue: [self pushLiteralConstantBytecode].
    (currentBytecode between: 64 and: 95) ifTrue: [self pushLiteralVariableBytecode].
    (currentBytecode between: 96 and: 103) ifTrue: [self storeAndPopReceiverVariableBytecode].
    (currentBytecode between: 104 and: 111) ifTrue: [self storeAndPopTemporaryVariableBytecode].
    currentBytecode = 112 ifTrue: [self pushReceiverBytecode].
    (currentBytecode between: 113 and: 119) ifTrue: [self pushConstantBytecode].
    currentBytecode = 128 ifTrue: [self extendedPushBytecode].
    currentBytecode = 129 ifTrue: [self extendedStoreBytecode].
    currentBytecode = 130 ifTrue: [self extendedStoreAndPopBytecode].
    currentBytecode = 135 ifTrue: [self popStackBytecode].
    currentBytecode = 136 ifTrue: [self duplicateTopBytecode].
    currentBytecode = 137 ifTrue: [self pushActiveContextBytecode]


There are single byte instructions that push the first 16 instance variables of the receiver and the first 16 temporary frame locations. Recall that the temporary frame includes the arguments and the temporary variables.

pushReceiverVariableBytecode
    | fieldIndex |
    fieldIndex  self extractBits: 12 to: 15
        of: currentBytecode.
    self pushReceiverVariable: fieldIndex
pushReceiverVariable: fieldIndex
    self push: (memory fetchPointer: fieldIndex
        ofObject: receiver)
pushTemporaryVariableBytecode
    | fieldIndex |
    fieldIndex  self extract Bits: 12 to: 15
        of: currentBytecode.
    self pushTemporaryVariable: fieldIndex
pushTemporaryVariable: temporaryIndex
    self push: (self temporary: temporaryIndex)


There are also single byte instructions that reference the first 32 locations in the literal frame of the active context's method. The contents of one of these locations can be pushed with pushLiteralConstantBytecode. The contents of the value field of an Association stored in one of these locations can be pushed with pushLiteralVariableBytecode.

pushLiteralConstantBytecode
    | fieldIndex |
    fieldIndex  self extractBits: 11 to: 15
        of: currentBytecode.
    self pushLiteralConstant: fieldIndex
pushLiteralConstant: literalIndex
    self push: (self literal: literalIndex)
pushLiteralVariableBytecode
    | fieldIndex |
    fieldIndex  self extractBits: 11 to: 15
        of: currentBytecode.
    self pushLiteralVariable: fieldIndex
pushLiteralVariable: literalIndex
    | association |
    association  self literal: literalIndex.
    self push: (memory fetchPointer: ValueIndex
        ofObject: association)


Associations are objects with two fields, one for a name and one for a value. They are used to implement shared variables (global variables, class variables, and pool variables). The following routine initializes the index used to fetch the value field of Associations.

initializeAssociationIndex
    ValueIndex  1


The extended push bytecode can perform any of the four operations described above (receiver variable, temporary frame location, literal constant, or literal variable). However, instead of a limit of 16 or 32 variables accessible, it can access up to 64 instance variables, temporary locations, literal constants, or literal variables. The extended push bytecode is followed by a byte whose high order two bits determine which type of push is being done and whose low order six bits determine the offset to use.

extendedPushBytecode
    | descriptor variableType variableIndex |
    descriptor  self fetchByte.
    variableType  self extractBits: 8 to: 9
        of: descriptor.
    variableIndex  self extractBits: 10 to: 15
        of: descriptor.
    variableType=0 ifTrue: [self pushReceiverVariable: variableIndex].
    variableType=1 ifTrue: [self pushTemporaryVariable: variableIndex].
    variableType=2 ifTrue: [self pushLiteralConstant: variableIndex].
    variableType=3 ifTrue: [self pushLiteralVariable: variableIndex]


The pushReceiverBytecode routine pushes a pointer to the active context's receiver. This corresponds to the use of self or super in a Smalltalk method.

pushReceiverBytecode
    self push: receiver


The duplicateTopBytecode routine pushes another copy of the object pointer on the top of the stack.

duplicateTopBytecode
    self push: self stackTop


The pushConstantBytecode routine pushes one of seven constant object pointers (true, false, nil, -1, 0, 1, or 2).

pushConstantBytecode
    currentBytecode = 113 ifTrue: [self push: TruePointer]. 
    currentBytecode = 114 ifTrue: [self push: FalsePointer]. 
    currentBytecode = 115 ifTrue: [self push: NilPointer]. 
    currentBytecode = 116 ifTrue: [self push: MinusOnePointer]. 
    currentBytecode = 117 ifTrue: [self push: ZeroPointer]. 
    currentBytecode = 118 ifTrue: [self push: OnePointer].
    currentBytecode = 119 ifTrue: [self push: TwoPointer]


The pushActiveContextBytecode routine pushes a pointer to the active context itself. This corresponds to the use of thisContext in a Smalltalk method.

pushActiveContextBytecode
    self push: activeContext


The store bytecodes transfer references in the opposite direction from the push bytecodes; from the top of the stack to the receiver's instance variables, the temporary frame, or the literal frame. There are single byte versions for storing into the first eight variables of the receiver or the temporary frame and then popping the stack.

storeAndPopReceivervariableBytecode
    | variableIndex |
    variableIndex  self extractBits: 13 to: 15
        of: currentBytecode.
    memory storePointer: variableIndex
        ofObject: receiver
        withValue: self popStack
storeAndPopTemporaryVariableBytecode
    | variableIndex |
    variableIndex  self extractBits: 13 to: 15
        of: currentBytecode.
    memory storePointer: variableIndex + TempFrameStart
        ofObject: homeContext
        withValue: self popStack


Stores into variables other than those accessible by the single byte versions are accomplished by two extended store bytecodes. One pops the stack after storing and the other does not. Both extended stores take a following byte of the same form as the extended push. It is illegal, however, to follow an extended store with a byte of the form 10xxxxxx since this would mean changing the value of a literal constant.

extendedStoreAndPopBytecode
    self extendedStoreBytecode.
    self popStackBytecode
extendedStoreBytecode
    | descriptor variableType variableIndex association |
    descriptor  self fetchByte. 
    variableType  self extractBits: 8 to: 9
                        of: descriptor. 
    variableIndex  self extractBits: 10 to: 15
                        of: descriptor. 
    variableType = O ifTrue:
        [memory storePointer: variableIndex 
                ofObject: receiver
                withValue: self stackTop]. 
    variableType = 1 ifTrue:
        [memory storePointer: variableIndex + TempFrameStart 
                ofObject: homeContext
                withValue: self stackTop]. 
    variableType = 2 ifTrue:
        [self error: 'illegal store']. 
    variableType = 3 ifTrue:
        [association  self literal: variableIndex. 
            memory storePointer: ValueIndex
                ofObject: association 
                withValue: self stackTop]


The last stack bytecode removes the top object pointer from the stack without doing anything else with it.

popStackBytecode
    self popStack


Jump Bytecodes

The jump bytecodes change the active context's instruction pointer by a specified amount. Unconditional jumps change the instruction pointer whenever they are encountered. Conditional jumps only change the instruction pointer if the object pointer on the top of the stack is a specified Boolean object (either true or false). Both unconditional and conditional jumps have a short (single-byte) and a long (two-byte) form.

jumpBytecode
    (currentBytecode between: 144 and: 151)
        ifTrue: [self shortUnconditionalJump].
    (currentBytecode between: 152 and: 159)
        ifTrue: [self shortConditionalJump].
    (currentBytecode between: 160 and: 167)
        ifTrue: [self longUnconditionalJump].
    (currentBytecode between: 168 and: 175)
        ifTrue: [self longConditionalJump]


The jump bytecodes use the jump: routine to actually change the bytecode index.

jump: offset
    instructionPointer  instructionPointer + offset


The eight short unconditional jumps advance the instruction pointer by 1 through 8.

shortUnconditionalJump
    | offset |
    offset  self extractBits: 13 to: 15
        of: currentBytecode.
    self jump: offset + 1


The eight long unconditional jumps are followed by another byte. The low order three bits of the jump bytecode provide the high order three bits of an 11-bit twos complement displacement to be added to the instruction pointer. The byte following the jump provides the low order eight bits of the displacement. So long unconditional jumps can jump up to 1023 forward and 1024 back.

longUnconditionalJump
    | offset |
    offset  self extractBits: 13 to: 15
        of: currentBytecode.
    self jump: offset - 4 * 256 + self fetchByte


The conditional jumps use the jumpIf:by: routine to test the top of the stack and decide whether to perform the jump. The top of stack is discarded after it is tested.

jumpIf: condition by: offset
    | boolean |
    boolean  self popStack.
    boolean = condition
        ifTrue: [self jump: offset]
        ifFalse: [(boolean = TruePointer) | (boolean = FalsePointer)
            ifFalse: [self unPop:1.
                self sendMustBeBoolean]]


The conditional jumps are used in the compiled form of messages to booleans (e.g., ifTrue: and whileFalse:). If the top of the stack at the time of a conditional jump is not true or false it is an error since an object other than a boolean has been sent a message that only booleans understand. Instead of sending doesNotUnderstand:, the interpreter sends mustBeBoolean to it.

sendMustBeBoolean
    self sendSelector: MustBeBooleanSelector
        argumentCount: 0


The sendSelector:argumentCount: routine is described in the next section on send bytecodes.


The eight short conditional jumps advance the instruction pointer by 1 through 8 if the top of the stack is false.

shortConditionalJump
    | offset |
    offset  self extractBits: 13 to: 15
            of:currentBytecode.
    self jumpIf: FalsePointer
        by: offset + 1


So, there are three possible outcomes to a short conditional jump:

  • If the top of the stack is false, the jump is taken.
  • If the top of the stack is true, the jump is not taken.
  • If the top of the stack is neither, mustBeBoolean is sent to it.


Half of the long conditional jumps perform the jump if the top of the stack is false while the other half perform the jump if it is true. The low order two bits of the bytecode become the high order two bits of a 10-bit unsigned displacement. The byte following the jump provides the low order eight bits of the displacement. So long conditional jumps can jump up to 1023 forward.

longConditionalJump
    | offset |
    offset  self extractBits: 14 to: 15
            of: currentBytecode.
    offset  offset * 256 + self fetchByte.
    (currentBytecode between: 168 and: 171)
        ifTrue: [self jumpIf: TruePointer
                by: offset].
    (currentBytecode between: 172 and: 175)
        ifTrue: [self jumpIf: FalsePointer
                by: offset]


Send Bytecodes

The send bytecodes cause a message to be sent. The object pointers for the receiver and the arguments of the message are found on the active context's evaluation stack. The send bytecode determines the selector of the message and how many arguments to take from the stack. The number of arguments is also indicated in the CompiledMethod invoked by the message. The compiler guarantees that this information is redundant except when a CompiledMethod is reached by a perform: message, in which case it is checked to make sure the CompiledMethod takes the right number of arguments. The perform: messages will be discussed in the next chapter in a section on control primitives.


The selectors of most messages are found in the literal frame of the CompiledMethod. The literal-selector bytecodes and the extended-send bytecodes specify the argument count of the message and the index of the selector in the literal frame. The 32 special-selector bytecodes specify the offset of the selector and argument count in an Array in the object memory. This Array is shared by all CompiledMethods in the system.

sendBytecode
    (currentBytecode between: 131 and: 134)
        ifTrue: [self extendedSendBytecode].
    (currentBytecode between: 176 and: 207)
        ifTrue: [self sendSpecialSelectorBytecode].
    (currentBytecode between: 208 and: 255)
        ifTrue: [self sendLiteralSelectorBytecode]


The literal-selector bytecodes are single bytes that can specify 0, 1, or 2 arguments and a selector in any one of the first 16 locations of the literal frame. Both the selector index and the argument count are encoded in the bits of the bytecode.

sendLiteralSelectorBytecode
    | selector |
    selector  self literal: (self extractBits: 12 to: 15
            of: currentBytecode).
    self sendSelector: selector
        argumentCount: (self extractBits: 10 to: 11
            of: currentBytecode) - 1


Most of the send bytecodes call the sendSelector:argumentCount: routine after determining the appropriate selector and argument count. This routine sets up the variables messageSelector and argumentCount, which are available to the other routines in the interpreter that will lookup the message and perhaps activate a method.

sendSelector: selector argumentCount: count
    | newReceiver |
    messageSelector  selector.
    argumentCount  count.
    newReceiver  self stackValue: argumentCount.
    self sendSelectorToClass: (memory fetchClassOf: newReceiver)
sendSelectorToClass: classPointer
    self findNewMethodInClass: classPointer.
    self executeNewMethod


The interpreter uses a method cache to reduce the number of dictionary lookups necessary to find CompiledMethods associated with selectors. The method cache may be omitted by substituting a call on lookupMethodInClass: for the call on findNewMethodInClass: in sendSelectorToClass: above. The lookupMethodInClass: routine is described in the previous chapter in a section on classes. The cache may be implemented in various ways. The following routine uses four sequential locations in an Array for each entry. The four locations store the selector, class, CompiledMethod, and primitive index for the entry. This routine does not allow for reprobes.

findNewMethodInClass: class
    | hash |
    hash  (((messageSelector bitAnd: class) bitAnd: 16rFF) bitShift: 2) + 1. 
    ((methodCache at: hash)=messageSelector
                and: [(methodCache at: hash + 1) = class]) 
        ifTrue: [newMethod  methodCache at: hash + 2.
            primitiveIndex  methodCache at: hash + 3] 
        ifFalse: [self lookupMethodInClass: class.
            methodCache at: hash put: messageSelector. 
            methodCache at: hash + 1 put: class. 
            methodCache at: hash + 2 put: newMethod. 
            methodCache at: hash + 3 put: primitiveIndex]


The method cache is initialized with the following routine.

InitializeMethodCache
    methodCacheSize  1024.
    methodCache  Array new: methodCacheSize


The executeNewMethod routine calls a primitive routine if one is associated with the CompiledMethod. The primitiveResponse routine returns false if no primitive is indicated or the primitive routine is unable to produce a result. In that case, the CompiledMethod is activated. Primitive routines and the primitiveResponse routine will be described in the next chapter.

executeNewMethod
    self primitiveResponse
        ifFalse: [self activateNewMethod]


The routine that activates a method creates a MethodContext and transfers the receiver and arguments from the currently active context's stack to the new context's stack. It then makes this new context be the interpreter's active context.

activateNewMethod
    | contextSize newContext newReceiver | 
    (self largeContextFlagOf: newMethod) = 1
        ifTrue: [contextSize  32 + TempFrameStart]
        ifFalse: [contextSize  12 + TempFrameStart].
    newContext  memory instantiateClass: ClassMethodContextPointer
                    withPointers: contextSize. 
    memory storePointer: SenderIndex
            ofObject: newContext
            withValue: activeContext. 
    self storeInstructionPointerValue:
                (self initialInstructionPointerOfMethod: newMethod) 
        inContext: newContext.
    self storeStackPointerValue: (self temporaryCountOf: newMethod) 
        inContext: newContext.
    memory storePointer: MethodIndex 
            ofObject: newContext
            withValue: newMethod. 
    self transfer: argumentCount + 1
        fromIndex: stackPointer - argumentCount 
        ofObject: activeContext
        toIndex: ReceiverIndex
        ofObject: newContext.
    self pop: argumentCount + 1.
    self newActiveContext: newContext


There are four extended-send bytecodes. The first two have the same effect as the literal-selector bytecodes except that the selector index and argument count are found in one or two following bytes instead of in the bytecode itself. The other two extended-send bytecodes are used for superclass messages.

extendedSendBytecode
    currentBytecode = 131 ifTrue: [self singleExtendedSendBytecode]. 
    currentBytecode = 132 ifTrue: [self doubleExtendedSendBytecode]. 
    currentBytecode = 133 ifTrue: [self singleExtendedSuperBytecode]. 
    currentBytecode = 134 ifTrue: [self doubleExtendedSuperBytecode]


The first form of extended send is followed by a single byte specifying the number of arguments in its high order three bits and selector index in the low order five bits.

singleExtendedSendBytecode
    | descriptor selectorIndex |
    descriptor  self fetchByte.
    selectorIndex  self extractBits: 11 to: 15
        of: descriptor.
    self sendSelector: (self literal: selectorIndex)
        argumentCount: (self extractBits: 8 to: 10
            of: descriptor


The second form of extended send bytecode is followed by two bytes; the first is the number of arguments and the second is the index of the selector in the literal frame.

doubleExtendedSendBytecode
    | count selector |
    count  self fetchByte.
    selector  self literal: self fetchByte.
    self sendSelector: selector
        argumentCount: count


When the compiler encounters a message to super in a symbolic method, it uses the bytecode that pushes self for the receiver, but it uses an extended-super bytecode to indicate the selector instead of a regular send bytecode. The two extended-super bytecodes are similar to the two extended-send bytecodes. The first is followed by a single byte and the second by two bytes that are interpreted exactly as for the extendedsend bytecodes. The only difference in what these bytecodes do is that they start the message lookup in the superclass of the class in which the current CompiledMethod was found. Note that this is not necessarily the immediate superclass of self. Specifically, it will not be the immediate superclass of self if the CompiledMethod containing the extendedsuper bytecode was found in a superclass of self originally. All CompiledMethods that contain extended-super bytecodes have the class in which they are found as their last literal variable.

singleExtendedSuperBytecode
    | descriptor selectorIndex methodClass |
    descriptor  self fetchByte.
    argumentCount  self extractBits: 8 to: 10
        of: descriptor.
    selectorIndex  self extractBits: 11 to: 15
        of: descriptor.
    messageSelector  self literal: selectorIndex.
    methodClass  self methodClassOf: method.
    self sendSelectorToClass: (self superclassOf: methodClass)
doubleExtendedSuperBytecode
    | methodClass |
    argumentCount  self fetchByte.
    messageSelector  self literal: self fetchByte.
    methodClass  self methodClassOf: method.
    self sendSelectorToClass: (self superclassOf: methodClass)


The set of special selectors can be used in a message without being included in the literal frame. An Array in the object memory contains the object pointers of the selectors in alternating locations. The argument count for each selector is stored in the location following the selector's object pointer. The specialSelectorPrimitiveResponse routine will be described in the next chapter.

sendSpecialSelectorBytecode
    | selectorIndex selector count |
    self specialSelectorPrimitiveResponse
        ifFalse: [selectorIndex  (currentBytecode - 176) * 2.
                    selector  memory fetchPointer: selectorIndex
                                ofObject: SpecialSelectorsPointer.
                    count  self fetchInteger: selectorIndex + 1
                            ofObject: SpecialSelectorsPointer.
                    self sendSelector: selector 
                        argumentCount: count]


Return Bytecodes

There are six bytecodes that return control and a value from a context; five return the value of a message (invoked explicitly by "↑" or implicitly at the end of a method) and the other one returns the value of a block (invoked implicitly at the end of a block). The distinction between the two types of return is that the former returns to the sender of the home context while the latter returns to the caller of the active context. The values returned from the five return bytecodes are: the receiver (self), true, false, nil, or the top of the stack. The last return bytecode returns the top of the stack as the value of a block.

returnBytecode
    currentBytecode = 120
        ifTrue: [self returnValue: receiver
            to: self sender]. 
    currentBytecode = 121
        ifTrue: [self returnValue: TruePointer 
            to: self sender].
    currentBytecode = 122
        ifTrue: [self returnValue: FalsePointer
            to: self sender]. 
    currentBytecode = 123
        ifTrue: [self returnValue: NilPointer 
            to: self sender].
    currentBytecode = 124
        ifTrue: [self returnValue: self popStack
            to: self sender]. 
    currentBytecode = 125
        ifTrue: [self returnValue: self popStack 
            to: self caller]


The simple way to return a value to a context would be to simply make it the active context and push the value on its stack.

simpleReturnValue: resultPointer to: contextPointer
    self newActiveContext: contextPointer.
    self push: resultPointer


However, there are three situations in which this routine is too simple to work correctly. If the sender of the active context were nil; this routine would store a nil in the interpreter's active context pointer, bringing the system to an unpleasant halt. In order to prevent this, the actual returnValue:to: routine first checks to see if the sender is nil. The interpreter also prevents returns to a context that has already been returned from. It does this by storing nil in the instruction pointer of the active context on return and checking for a nil instruction pointer of the context being returned to. Both of these situations can arise since contexts are objects and can be manipulated by user programs as well as by the interpreter. If either situation arises, the interpreter sends a message to the active context informing it of the problem. The third situation will arise in systems that automatically deallocate objects based on their reference counts. The active context may be deallocated as it is returning. It, in turn, may contain the only reference to the result being returned. In this case, the result will be deallocated before it can be pushed on the new context's stack. Because of these considerations, the returnValue: routine must be somewhat more complicated.

returnValue: resultPointer to: contextPointer
    | sendersIP |
    contextPointer = NilPointer
        ifTrue: [self push: activeContext.
                    self push: resultPointer.
                    self sendSelector: CannotReturnSelector
                        argumentCount: 1].
    sendersIP  memory fetchPointer: InstructionPointerIndex
                            ofObject: contextPointer.
    sendersIP = NilPointer
        ifTrue: [self push: activeContext.
                    self push: resultPointer.
                    self sendSelector: CannotReturnSelector
                        argumentCount: 1].
                    memory increaseReferencesTo: resultPointer.
                    self returnToActiveContext: contextPointer.
                    self push: resultPointer.
                    memory decreaseReferencesTo: resultPointer


This routine prevents the deallocation of the result being returned by raising the reference count until it is pushed on the new stack. It could also have pushed the result before switching active contexts. The returnToActiveContext: routine is basically the same as the newActiveContext: routine except that instead of restoring any cached fields of the context being returned from, it stores nil into the sender and instruction pointer fields.

returnToActiveContext: aContext
    memory increaseReferencesTo: aContext.
    self nilContextFields.
    memory decreaseReferencesTo: activeContext. 
    activeContext  aContext.
    self fetchContextRegisters
nilContextFields
    memory storePointer: SenderIndex 
        ofObject: activeContext
        withValue: NilPointer.
    memory storePointer: InstructionPointerIndex
        ofObject: activeContext 
        withValue: NilPointer


Notes